Search:

Just ignore him. The razor tail its more efficient and works just fine

Sent from my Motorola Electrify using Tapatalk 2

I have crashes my razor 450 4x, have not damaged the main great yet. They seem to be pretty sturdy

Sent from my Motorola Electrify using Tapatalk 2

Upload to YouTube then post the link

Sent from my Motorola Electrify using Tapatalk 2

And they cost 3x as much. Its all what you want :p

Sent from my Motorola Electrify using Tapatalk 2

At least once you work out all they issues, they actually fly pretty nice.

Sent from my Motorola Electrify using Tapatalk 2

If you move it closer it will have less leverage and work even less. If you want more rudder, you need faster motor, bigger blades or longer tail.

Don't forget to check your cg. That could be...

not sure why you would want that. what if the optimal setting is between ratchets?

but as long as you are happy.

cant say I agree. my nano-techs specifically say they can take 8C charging safely. I have only charged at about 3C and they didnt even get warm.

you are looking at a brushless conversion.

you will need:

brushless convertor board (converts from DC motor to brushless control)
ESC
brushless motor

finding a motor with enough speed (kv)...

More than likely you need to calibrate your esc. Turn on tx, put the throttle all the way up, then plug in model. Wait for beeps then put throttle down. Done

Sent from my Motorola Electrify...

Looks like the gy192 gyro. I never did get mine to hold for nothing. I have the hk 401b right now, solid as a rock and only $12. Will worth getting a good gyro.

But you still have to get it...

For AA batteries? Go to rat shack. They are mostly likely nimh

Sent from my Motorola Electrify using Tapatalk 2

I would just replace the "AA" pack with a lipo or life pack. hobby king has ones specifically designed for TX duty and are only about $12.

the recon TX is not a great TX, but you can fly the razor fairly well once you set it up correctly. read this whole thing on how it works and understand how a CCPM works back and forward and you...

do you have training gear on the heli? that will help tons to get the tail setup. it will allow it to spin on the ground (where it is safe, lol) I would not be flying any heli where you cant...

I know what you mean.
Maybe you have some inventing to do, lol

Sent from my Motorola Electrify using Tapatalk 2

Do you use a lanyard?

Sent from my Motorola Electrify using Tapatalk 2

gain and mode have nothing to do with it drifting. that has all to do with how much pitch is in the blades. depending on which way it is drifting you need more pitch or less. on the erazor just...

With a small amount of tinkering, you can add a spek module to a th9x and it will be dsm2 and dsmx compatible as well as stock

As for for channels. With er9x you can use 2rx and get 16 channels. ...

for the money I dont think the TH9x is all that bad. I have had one for more than 6 months and I love it. I have the backlit mod and the ER9x firmware upgrade. I can do everything a Dx8 can do and...

That doesn't sound too bad. Bent main shaft is gonna happen just about every time you crash.
The Dynam servos are cheap and need replacing anyway :D
Check you feathering shaft and make sure your...

Yup about half turn. You were right. And yes tracking is bang on as well :D

Sent from my Motorola Electrify using Tapatalk 2

Eureka! I got it! found that a couple of the screws for the flybar craddle were loose. not much but appearantly enough.

tightened them up and it hovers nice and stable again.

Thanks to...

the th9x has a -100 to +100 range. so "70" is actually 85%. I have three curves

ID0: -100 -25 50 75 100 for spool up
ID1: for normal flying 70 70 70 85 100
ID2: for 3D(dont use it yet) 100 85...

Throttle curve: 70 70 70 85 100
That is after spin up obviously.

One way seems solid. I can torque the gears pretty hard and it doesn't slip.

Jesus bolt is in place and intact. I have tried...